How To Assemble A Desktop PC/Choosing the parts
The
The first step to building a computer is acquiring the parts. This
guide will start with a quick explanation of essential parts and
elaborate on them further on.
A computer is made up of a case (or chassis) which
houses several important internal components, and provides places to
connect the external components, including non-peripherals.
Inside the case go the following internal parts:
- Power Supply/PSU – power supply unit, converts outlet power, which is alternating current (AC), to direct current (DC) which is required by internal components, as well as providing appropriate voltages and currents for these internal components.
- Motherboard/mainboard – As the name indicates, this is the electronic centerpiece of the computer: everything else connects to the motherboard.
- Processor/CPU – central processing unit, the "brain" of the computer, most actual computation takes place here.
- RAM – random access memory, the "short-term memory" of a computer, used by the CPU to store program instructions and data upon which it is currently operating. Data in RAM is lost when the computer is powered off, thus necessitating a hard drive.
Optional components follow: (Components that depend on the function that will be given to the machine)
- Hard Drive/Hard Disk – the "long-term memory" of the computer, used for persistent storage – i.e. the things stored on it remain even when the computer is powered down. The operating system, and all your programs and data are stored here.
- Optical Drive – device for reading/writing optical disks. May read CDs, DVDs, or other optical media, depending on the type. It is essential for installing many operating systems and programs. It may be able to write some of these discs, as well. Some people like to have two such drives for copying disks.
- Video Card/Graphics Card/GPU – does processing relating to video output. Some motherboards have an "onboard" GPU built in so you don’t need (but may add) a separate video card. Otherwise, you will need a video card. These plug into a slot on the motherboard and provide a place to connect a monitor to your computer.
On top of the internal components listed above, you will also need these external components:
- Keyboard – for typing on. Many motherboards won't even boot without a keyboard attached.
- Mouse – for pointing and clicking. Unless you chose a text-based operating system, you will likely want one of these.
- Monitor – This is where the pretty pictures go. They come in many forms, the most common being CRT and LCD.
These are the parts that a standard PC will use. We are not
considering such esoterica as headless, touchscreen, or voice-controlled
systems. You might want to make a check list (perhaps using a
spreadsheet) of parts to use as you go about your process of research
and selection. That way you won’t find yourself sitting down with a pile
of brand new hardware only to find that you forgot an essential
component.
Before you jump onto the web and start spending lots of money on
expensive computer parts, there are three important questions you should
answer which will guide your purchases:
- What will be the main function of the computer?
- What useful parts do you have on hand, from an old computer or otherwise?
- How much can you afford to spend on the system?
What operating system am I going to use?
Before you buy components, be sure that they are supported by the
operating system you plan to use. Almost all commonly available PC
devices have drivers (small programs that allow the operating system to
recognize and work with a hardware device) available for current
versions of Windows (generally, 2000, XP, Vista, 7 or newer); if you
want to run an alternative operating system, you'll have to do some
research; many alternatives have extensive 'Hardware Compatibility
Lists' (HCLs) as well as software compatibility.
Main operating systems available
- Microsoft Windows - 2000 (2k), XP (Home/Pro), Vista and 7 (Home/Business/Ultimate)
- Popular GNU/Linux Distros - Red-Hat, Ubuntu, Knoppix, SuSE, Fedora, Debian, Parsix, and others
- Popular BSD Variants - FreeBSD, OpenBSD, NetBSD, and others
- BeOS - No longer supported by the original creators, but was taken over as an open source project
- DOS - MS-DOS, PC-DOS, DR-DOS, FreeDOS, etc - Disc Operating System
Windows information and hardware support lists
Microsoft Windows is a series of operating systems made by the
major software corporation Microsoft. Nearly everybody who has worked
with computers has used Windows in some way or another. Windows is ideal
for most personal computing and fits the needs (or wants) of just about
anyone: gamers, video/graphics editors, office workers, or the average
guy who wants to surf the web and play a bit of solitaire here and
there. Today, Windows XP, Windows Vista, and Windows 7 are the three
most common versions of the operating system (Windows 7 being the
latest, Windows XP being the most common of the three).
Windows in general supports most processors and motherboards based on
the i386 (x86; 32-bit) or x86_64 (AMD64/EM64T; 64-bit) architectures.
Put simply, all available consumer processors (especially from AMD or
Intel) will work with the Windows XP operating system, as well as most
internal and external devices, including Wireless Receivers, Graphics
Cards/GPUs, and Storage Devices.
For other hardware, see Microsoft's compatibility list.
GNU/Linux information and hardware support lists
As one of the most popular open-source (free) operating systems, GNU/Linux
is a very good (and popular) alternative. Linux is a UNIX-like series
of operation systems and comes in many different distributions (AKA
"distros"), such as Ubuntu, Debian, openSuSE, Fedora, and Mandriva.
Linux can perform many of the same functions as Windows and features
similar programs. Linux is also much more flexible than Windows because
it's open-source, making it developer-friendly. Some companies also sell
versions of Linux with technical support.
Linux has versions for many different architectures, including i386,
x64 and PowerPC. It also support all kinds of processors, enabling it to
be used on Palm PCs and even iPods. There are many different versions
of Linux, produced by different companies and organizations. These are
called 'distributions' or 'distros' for short. For a desktop PC, you
should make sure to pick a desktop distribution, one where the
company/organization has desktop users in mind, e.g. Ubuntu, Fedora, or
Mandriva. It should be noted, however, that many popular programs,
especially games, are not available for Linux, and the only way to run
them is with special compatibility layers or programs like Wine, which
may or may not work with a specific program. Even if you manage to get a
certain program running, you may still encounter issues in the
program's emulation.
All this is important to bear in mind as different distributions will
support different hardware (generally more 'bleeding-edge'
distributions will support newer hardware – look at Fedora, SuSE,
Ubuntu, compared to the latest stable release of Debian). A good rule of
thumb to ascertain compatibility, is to buy hardware that is 12 to 18
months old, as it most likely has Linux support with most distributions,
but won't be too old. You may also buy newer hardware, and if it
follows common standards (eg. x86, ISA, SATA), it should be supported.
BSDs information and hardware support lists
BSD, or the Berkeley Software Distribution, is also a
UNIX-Like series of operating systems and could be considered the
alternative to Linux (an alternative to an alternative?). Now, BSD is an
open-source (free) operating system and has its own descendants, such
as FreeBSD and OpenBSD. BSD Hardware Support is similar to Linux's - it
can handle most hardware. Unlike Linux, however, BSD tends not to
support "new" hardware (such as Core i7 and Xeon processors) but can
handle a lot of both older and modern components. FreeBSD is also very
compatible with many Linux applications as they are both UNIX-based and
can be installed on a variety of platforms (even Xbox consoles!)
- DesktopBSD, see FreeBSD 5.4/i386 and FreeBSD 5.4/amd64
- Dragonfly BSD
- FreeBSD
- NetBSD
- OpenBSD
- PC-BSD, see FreeBSD 6.0/i386
What will be the main function of the computer?
If you're going to build a computer from scratch for a specific
purpose, you'll want to keep that purpose in mind when choosing your
components; don't just go to the store or an online shop and start
buying. Consider what you want to use the computer for, you may be able
to save money by specifying expensive, premium parts only where needed.
Any reasonably configured computer built from current components will
offer adequate Internet browsing and word-processing capabilities. For
an office computer, this is often all that is needed. As long as you
provide enough RAM for your chosen operating system (256 MB to 1 GB for
XP or Linux, 2 GB for Vista) any processor you can buy new will provide
acceptable performance. If the computer is for gaming, a fast processor,
the addition of a high-end graphics accelerator card (or two) and extra
RAM will provide a more satisfactory gaming experience. Besides gaming,
computers intended for video editing, serious audio work, CAD/CAM, or
animation will benefit from beefier components which are specifically
designed for that purpose.
Here are some general system categories. Your own needs will probably
not fit neatly into one of these, but they are a good way to start
thinking about what you are going to use your computer for. With each
we’ve indicated the components you should emphasize when building the
system.
Simple web surfer
To provide basic functionality to a user who just needs web surfing, a
little word processing, and the occasional game of solitaire, it’s
important not to go overboard. Such a user has no need for a top of the
line processor or 3D graphics card. A modestly configured system with an
adequate Internet connection will suit this user best and can be
assembled quite cheaply.
This usage pattern is not going to stress any particular component,
you should be looking at a mid- to low-level processor (historically,
and currently, at about the $125 price point or less), enough RAM for
the OS and a mother board with built in Ethernet, video and audio. You
can use a mid-level case/power supply combo (these components are often
sold as a pair).
If you have a little extra money, spend it on a better monitor, mouse/keyboard, and case/power supply in that order.
Office computer
An office computer can be expected to do word processing, spreadsheet
and database work, network access, e-mail and a little light
development of spreadsheets, databases, and presentations. It might also
be called on to do page layout work, some 2D graphic creation, and/or
terminal emulation.
None of this stresses any particular component either, but since
office workers often run several applications at the same time, and
because time is money in this space, a strong mid-level processor is
suggested. Typically this would be the processor one or two places from
the top of the line. Plenty of RAM will also facilitate multitasking and
save time.
You will not need much in the way of 3D graphics but you’ll want to
make sure that the video subsystem has its own memory rather than using
system RAM. Many integrated video systems do this and it can really slow
things down. A cheap (sub $75) (for this and other prices in US dollars
see www.xe.com/ucc
or other currency converter of your choice for conversion into your
local currency) video card with 64MB or more can be a good investment.
You’ll want a sturdy case (computers kept under desks get kicked by
users and poked by cleaning staff) with a reliable power supply but
nothing fancy. If you plan on keeping the system running nearly all the
time, look for a power supply with a good reliability record. Any extra
budget after the above should focus on a better monitor, better/more
ergonomic mouse/keyboard and more RAM.
Server
A server these days can be anything from a home unit serving MP3's
and homework files to the kids, to a machine running a business-critical
system for a small business, to a 3u rack mount unit serving up
millions of hits a day on the Internet.
The thing that most servers have in common is that they are always on
and therefore reliability is a key characteristic. Also they serve more
than one user while storing and processing important information. For
this reason servers are often equipped with redundant systems such as
dual power supplies, RAID 5 arrays of four or more hard disks, special
server grade processors that require error-correcting memory, multiple
high-speed Ethernet connections, etc.
All of this is a little beyond the scope of the current work, but, in
general, servers need lots of RAM, fast redundant hard drives, and the
most reliable components your budget will allow. The CPU choice should
be made in accordance with the use of the server. A simple print/fax
server will do fine with a CPU stolen from a museum, whereas a server
running a database and a front end for that, will work much better with a
top of the line CPU.
On the other end of the hardware list, since nobody is usually
sitting at them, you can get away with the cheapest possible keyboard,
mouse and monitor (in fact many servers run "headless" with no monitor
at all). Graphics are also a very low priority on these machines, and a
read only CD/DVD-ROM optical drive (used, infrequently, for installing
software and updates) will do just fine.
Gaming system
We’re not talking here about the occasional game of solitaire or a
secret late night Zuma obsession. We’re talking about cutting edge 3D
gaming – first-person shooters or real-time strategy games with
thousands of troops on the screen at the same time, with anisotropic
filtering and anti-aliasing and mip-mapped specular reflections and a
lot of other confusing terminology describing visual effects that will
make anything less than a top-of-the-line system fall down on its knees
and beg for mercy.
A top of the range processor is not critical to gaming performance
(though it does help), but you will need at least a mid range one and
plenty of RAM, as well as a motherboard to match, since the speed of the
motherboard buses can limit high-end components. Please remember that
if you plan on running the latest games in 1080p on highest settings, or
even with three monitors, you will need a high end processor. This will
stop the chances of bottlenecking the GPU (Graphic Processing Unit) and
not give you the gaming experience you need. The most important part
will be the video card (or cards) with cutting edge GPUs. ATI (who have been bought by AMD so the ATI cards now are labelled as AMD) and NVIDIA
have been competing for "king of the graphics card" honors for years
and the competition is so keen that new cards running on new GPUs are
released, it seems, twice a month. If you want to run two or more
screens, the best idea would be to run two or more cards in either
Crossfire X (AMD) or SLI (NVidia). But this is expensive and not all
motherboards support both company's methods, so do your research and buy
the best current cards you can afford.
The other component which can offload some of the burden from your
CPU is a good audio card. The DSPs (Digital Signal Processors) on the
audio card can take over a lot of the sound processing and free up the
CPU for other tasks. Currently Creative Labs
pretty much owns this space, but again do your research (partly by
reading on) and get the best audio card you can afford. Some
motherboards have audio cards already built in, though these are
generally of lesser quality. Although, this depends on the quality of
the motherboard.
Finally all of these components are going to require a pretty hefty
power supply, particularly if you decide to run two graphics cards in
Crossfire (ATI) or SLI (NVIDIA) mode, in which case make sure the power
supply is rated for the dual-graphics card mode you choose. Generally a
serious gaming rig will require at least a 500 watt supply; units are
available up to 1000 watts (1 Kilowatt) and two Kilowatt supplies have
been announced. Keep in mind that having a higher-rated power supply
will not actually increase the power your computer draws. The rating is
the maximum that the power supply is designed to provide. Get the best
you can afford.
As you may have noticed, pretty much every component inside the
computer needs to be top of the line; the same is true outside the case.
You’ll want a big monitor, and a high sensitivity mouse. There are even
gaming keyboards with the keys specially arranged, not to mention
joysticks, throttle controllers, driving wheels, etc.
So, given that your budget is not bottomless, how do you prioritize?
Well, the processor and video card are the components that will have the
most effect on your gaming performance. Next comes the motherboard and
RAM. If you use one instead of two video cards, you can also use a less
expensive power supply. One of the advantages to building your own
computer is that you can get the components you can afford now and plan
to upgrade them later.
A note on cases for gaming rigs – it is not necessary to get a case
with a side window that reveals glowing blue fans and revolving animated
heat-sinks. A well-built plain case will do just as well and let you
spend more money on the components that matter. But if you have the
cash, and that’s your taste, there are lots of flashy add-ons available
these days.
Entertainment system/media center
This is a computer designed to sit in the living room with the rest
of your A/V gear. The idea is that it will record and serve audio and
video files for replay via your existing television and stereo. The
current notion is that this computer should be built in a special case
that makes it look more like a stereo component, the size of which can
present a challenge when it comes to getting all the necessary parts
fitted.
For this system a mid-range processor will be fine, along with a
generous amount of RAM. A fast Ethernet connection will facilitate
sharing large files. You’ll also want a TV tuner card (or two) to get
video in and out of the machine. Many of these also provide DVR (digital video recorder) functionality, often without the monthly subscription fees and DRM
(digital rights management) restrictions required by companies like
Tivo. A wireless keyboard and mouse provide for couch-based use and a
separate monitor may be unnecessary as your TV will fill that role.
All components should be as quiet as possible since you'll likely be
watching/listening in the same room. For this application it makes sense
to trade a little power for passively-cooled (without fans) parts.
Following this logic, one may consider fan-less CPUs and mainboards.
Workstation
A workstation was, originally, a single-user computer with more
muscle than a PC, intended to support a demanding technical application,
like CAD or complicated array-based simulations of real world
phenomena. The niche that these computers filled – between high end PC’s
and low end minicomputers – has essentially evaporated. The serious
scientific applications have migrated to clusters of PC's with near
super-computer speeds, and end-user applications, like video editing,
music production and CAD, run well on high-end PC's. One sector that
still uses large workstation farms from Sun or Silicon Graphics is
serious, Pixar-style animation.
For any of the following uses, you will need the fastest processor and the most RAM you can manage.
Note: On a Microsoft OS (anything before Vista 64x), the maximum
practical RAM available for programs is 3 Gigabytes. the 4th gigabyte
will be partially absorbed by system overhead.
Video editing
Big and fast hard drives are key. 10000 RPM Raptors in Raid 0 as
working space with multiple 750 GB drives or 1 Terabyte drives for
storage is a good target. SATA/300 is highly recommended and SCSI
subsystems should also be considered. A large amount of memory (4 gig or
more, depending on your OS and hardware limitations) would be
beneficial, as would a fast CPU, especially if you intend to render
effects or wish to quickly transcode video.
Music production
Plenty of disk space is important, you'll also want at least 2 GB of
RAM, but a music production (recording and mixing) workstation is
chiefly distinguished by specialized external components – studio
reference monitors instead of normal speakers, mixing consoles,
microphones, etc. If you want to record external sources, like vocals or
instruments, you'll need an audio interface which allows you to plug
mics or instruments into your computer.
Audio interfaces allow anything from a single microphone or
instrument on up to pro level systems that have 32 or more simultaneous
inputs. These separate inputs will allow you to record each one as a
separate track in your DAW. Most use Steinberg's ASIO interface (a
software driver that connects your hardware to your DAW software). If
you don't wish to invest in anything other than the onboard sound card
your computer comes with, consider ASIO4All, a free driver that imitates
the ASIO framework for almost any sound card.
One piece of advice, if you have extra money, get better microphones - even if you have to trade the Bluesmobile.
CAD/CAM
(Computer Assisted Design / Computer Aided Manufacturing)
A CAD/CAM workstation is usually a machine that runs a single, very
intense, application. These machines often utilize specialized video
hardware, like the Nvidia Quadro series of GPU's, which are designed
specifically for CAD/CAM rendering. Since these machines are usually
devoted to a single, expensive, application it's especially important to
pay close attention to the requirements of that application. Spec the
hardware to support the software - always a good idea but especially
important here.
Some examples of this specialized software are 3ds Studio Max, Maya, AutoCAD and Maxwell Render Engine.
Do I plan on overclocking my computer?
Overclocking consists of running components at faster internal speeds than they are rated for. If you are serious about overclocking
your computer, you need to do extensive research into the components
you select, as some parts respond to overclocking better than others.
Processors that respond well to heavy overclocking are generally not
very expensive (though overclockable memory is), but the price of a
component is by no means a guarantee of its overclocking potential.
Overclocking usually voids your warranty and is risky (you can destroy
your entire computer), so be warned! You need to think hard about
cooling the computer as overclocking generates heat. Anything from a few
extra fans to a liquid-cooled system may be necessary depending on the
nature of your system.
Do I plan on underclocking my computer?
This can be ideal for always-on entertainment systems. Underclocked
parts run cooler, often enabling passive cooling options to be used,
which leads to a much quieter system.
The risk here is not destroying your computer, as with overclocking,
but possible problems with hard-disk data integrity. It is a good idea
to back up your disk data periodically on a non-volatile medium, such as
DVDs or tape.
Can I use any of the parts from my old computer?
This depends on your situation; if your computer is more than four
years old, chances are that most of the parts will be too old, slow or
incompatible for your new machine. On the other hand, if you are
upgrading from a fairly new machine, you may be able to use many of the
parts. All of this assumes the old computer will no longer be used. If
you, or someone else, is going to continue using your old computer, it's
probably best just to leave it intact.
One important point – if you are selling your old computer it's a
good idea to erase the hard drive before giving it to its new owner.
Special precautions must be taken to ensure that you are not giving away
your sensitive or personal information. Don't forget that a simple
'delete' command does not actually erase the data on your hard drive.
The original data will still be present and can later be recovered by
someone else using special programs and/or equipment. To avoid this,
programs are available that will effectively 'shred' your data, making
it unrecoverable. Driver floppies or CD's that come with some hard
drives may also have programs to do this, that write 0s or 1s (either
way, "blankness") to the whole drive. Lower-tech approaches include
drilling a few holes in the drive or taking a blowtorch to it.
Obviously, either prevents it from being used again.
Since monitor technology moves quite slowly, you can probably keep
your current monitor and use it on the new computer if it's of
sufficient size and clarity for your work. The same can go for
keyboards, as well as mice, printers, scanners, and possibly speaker
sets. On the inside, you may be able to take out the floppy drive,
CD-ROM drive, and possibly the sound card and hard drive (depending on
how good they are, of course). Sometimes so much is used from the old
computer, that the line between an upgrade and a new computer can become
blurred.
Reusing a hard drive is an easy way to keep data from your old
computer. With most Windows operating systems moving a boot drive from
one motherboard to another will entail a series of reboots and
installation of new drivers. In the case of newer Windows systems, like
2000 and XP, an entire 'refresh install' may be necessary to allow
Windows to install a new Hardware Abstraction Layer. Back up your data
before trying this.
Where do I find the parts?
Once you have decided what you’re going to use your computer for, and
have reviewed which parts are available for reuse, you should make a
list of what components you will need to buy. A few hours of research
can save you years of regret, so make sure that the computer you build
will do what you need it to do.
Computer terminology can be confusing, so if there are terms you
don’t understand, be sure to look them up. Wikipedia is an excellent
place to start if, for example, you’re not clear on the difference
between, say, DDR and DDR2 memory.
There are several places to buy parts:
- Internet retailers generally offer the best price for new parts. If a part needs to be returned, you may be stuck for the shipping; check return policies before you purchase.
- Auction sites like eBay and several others offer very good prices for used parts. This is especially useful for parts which do not wear out. Returns can be problematic or impossible. Some auctions may not be legitimate. Always check the shipping cost before you bid.
- Local PC shops - Their prices are often higher, but they may make up for this by providing a lot of expertise. Get opinions from other sources, however, as they may be eager to sell you parts you don't need.
- Big local retailers often lack technical expertise and charge higher prices, but can be useful because they usually handle returns quickly. Also good if you need something right away.
- Trade shows that occur from time to time also provide a good place to shop, as the prices are often significantly reduced, and the variety of prefabricated computers built towards specific computing needs tend to be higher.
Also, your local town dump may have a special section for computers
and monitors that others have got rid of. These can be more or less
brand new computers with trivial problems such as a busted power supply
or faulty cables. Of course if the dump does have such a section, you
should ask permission of those in charge. They're usually glad to let
you go through it, but don't leave a mess. Taking advantage of this can
yield incredible finds, with a price tag of nothing or very little.
OEM vs Retail
Many hardware manufacturers will sell the same components in both OEM
and Retail versions. Retail hardware is intended to be sold to the
end-user through retail channels, and will come fully packaged with
manuals, accessories, software, etc. OEM stands for "original equipment
manufacturer"; items labeled as such are intended to be sold in bulk for
use by firms which integrate the components into their own products.
However, many online stores will offer OEM hardware at cheaper prices
than the corresponding retail versions. You will usually receive such
an item by itself in an anti-static bag. It may or may not come with a
manual or a CD containing drivers. Warranties on OEM parts may often be
shorter, and sometimes require you to obtain support through your
vendor, rather than the manufacturer. OEM components are also sometimes
specified differently than their retail counterparts, parts may be
clocked slower, and ports or features may be missing. Some of the
support may be less (as in the case of Microsoft). Again, do your
research.
What should affect the choice of any part/peripheral?
Many things should be taken into account when deciding what parts to buy. Below are some things to consider.
Compatibility
You’ll want to make sure that all the parts you buy work together
without problems. The CPU, the motherboard, and the RAM in particular
must be compatible with each other. Check the motherboard manufacturer's
web site; most will list compatible RAM and processors. Often quality
RAM that is not on the approved list (but is of the proper type) will
work anyway, but the manufacturers list of processors should be rigidly
adhered to.
Again, you’ll also want to make sure that your operating system
supports the hardware you choose. Windows is supported by almost
everything, though watch out for older components if you're planning on
using Vista. If you have any interest in running Linux, MacOS or another
operating system now or in the future, buy parts that are supported by
that OS (Operating System). It is also worth checking around the
Internet to make sure there is no history of your chosen components
clashing (e.g. certain combinations of hardware causing instability,
crashing, etc.)
Ergonomics
Ergonomics is the science of designing things so that they work with
the human body. This is obviously important when choosing peripherals
such as a keyboard or mouse but should also be considered when selecting
a monitor, and especially when setting up the computer for your use. If
your wrist hurts or you’re getting a crick in your neck, look at the
physical setup of your computer, check your chair height and posture. An
ounce of prevention here can avert troublesome repetitive strain
injuries.
Operating temperature
Modern components, notably processors, GPUs, RAM, and some elements
on the motherboard, are very small and draw a lot of power. A small area
doing a lot of work with a lot of power leads to high temperatures.
Various factors can cause electronic parts to break down over time and
all of these factors are exacerbated by heat. Very high temperatures can
burn out chips almost instantly, while running hot can shorten the
useful life of a part, so the cooler we can make these parts, the
better.
If you are not going to overclock your system, stock air cooling,
when paired with a good case with adequate fans, should be enough to
keep your system cool. If you want a quiet computer then components
designed for passive (fan-less) cooling can be paired with very low
noise case fans (or a well-vented case). In general, high-end parts will
require more attention to cooling.
To keep your system at a proper operating temperature, you can
monitor vital components with software (which usually comes with your
motherboard). If you are seeing high temps, make sure the interior of
your case is dust free, and remember that most cooling solutions can not
reduce the temperature of your computer parts below room temperature.
Of course, unless you happen to have your computer outdoors in a climate
such as the Sahara, room temperature will be well within the thermal
limits of any component on your computer.
Which brings us to overclocking. It's specialty cooling solutions
that make overclocking possible, a processor that might run stable at a
maximum of 3.3 GHz at 60C could hit speeds as high as 5 GHz with
specialized cooling systems. A sensible person wanting a 20% overclock
could add a special fan/heatsink to his CPU and some extra case fans. An
enthusiast seeking a major overclock might go with a water-cooling
solution for the CPU and GPU and sometimes other chips. The real
fanatics have been known to use liquid nitrogen or total immersion in
pure water or oil. You should not try any of the more extreme solutions
unless you really know what you're doing.
Price
Today, there are a wide array of hardware components and peripherals
tailored to fit every home computing need and budget. With all these
options to choose from, it can be a bit overwhelming if you've never
bought computer parts before. Shop around and remember to factor in
shipping and handling, and taxes. Some places may be priced a bit
higher, but offer perks such as free shipping, limited warranties, or
24-hour tech support. Many websites, such as CNET and ZDNet offer comprehensive reviews, user ratings, and links to stores, including price comparisons.
Since prices for any given part are always falling, it’s tempting to
just wait until the part you want goes down in price. Unfortunately the
reason prices decline is that better/faster parts are coming out all the
time, so the part you want this year that costs $500 may well be $200
next year, but by that time you won’t want it any more, you’ll want the
new, better part that still costs $500. At some point you’ve got to get
on the bus and ride, even if the prices are still falling.
Usually the best bet is to buy just behind the bleeding edge, where,
typically, you can get 90% of the performance of the top of the line
part for 50% or 60% of the price. That last 10% is very expensive and if
you don’t need it, you can save a lot of money with the second-tier
part.
It's a good idea to think about future upgradeability when selecting
some components. While the computer that you're building today may be
fine for your current needs you may want to upgrade it later. So look
for components that support the newest standards and have room for
future expansion, like a motherboard that will allow you to fit more
memory than you are planning to use, or a case that has room for extra
hard drives. If your current machine is maxed out the only possible
upgrade is often a new machine.
You may also find that by over-specifying in some areas you can save
money on others, e.g. if you don't currently need fantastic sound but
you do need IEEE1394 (Firewire, iLink) then you might want to purchase a
sound card anyway as some of the higher end sound cards also have a
IEEE1394 port.
Performance
If money is no object, this is an easy question; just buy the most
powerful components you can find. If, like most of us, there are limits
to what you can/want to spend, then focus on those areas where more
powerful parts will pay off for you and scrimp on others. Always look
for that sweet spot on the price/performance curve where you get the
most bang for your buck.
Primary components
These are the components that will be the core of your new computer.
It is impractical to put together a PC compatible computer without these
components and a bare set of peripherals.
Chassis (case) & power supply
1 Monitor
2 Motherboard
3 CPU (Microprocessor)
4 ATA sockets
5 Main memory (RAM)
6 Expansion cards
7 Power supply unit
8 Optical disc drive
9 Hard disk drive (HDD)
10 Keyboard
11 Mouse
In earlier eras most cases were beige, and since most components drew
far less power than similar components do now, power supplies received
little attention. Recently, however, cases for the home market have
become considerably more elaborate, with lights, side windows,
glow-in-the-dark cables and other shiny/glowing embellishments. Cases
now come in a plethora of styles and colors to suit anyone's taste. And
as current components require much more power, power supply quality and
size is an important issue.
If you are only building an office computer, the style of case will
be of little concern to you. You might want an inexpensive ATX case (ATX
is a specification which refers to the size of the motherboard. Any ATX
motherboard, and the parts designed therefore, will fit in any ATX
case), and an inexpensive power supply as you won't be running a
high-end processor or graphics card. As a guide, you’ll want a power
supply with a rating of more than 300 watts; any less won’t reliably
power modern components. Most case/PSU bundles are adequate, but tend to
feature a lower quality power supply than those that are sold
separately from cases. If possible, avoid power supplies with sleeve
bearing fans, as these are of considerably lesser quality.
Before purchasing any PSU, make sure that the supplied wattage is
sufficient for your components. Power requirements are usually listed in
the manuals that came with your components. It is important to note a
power supply's total power, and the power at each voltage: 3.3, 5 and
12V. If any of these do not meet your requirements, the rest of the
specifications don't matter.
Some companies have calculators to help you determine what your power
supply needs are; if you are the type to just plug in the numbers
without reading the details, you should buy a power supply that is 1.5
to 2 times the wattage that results from these calculators.
For a quiet system, you can choose a fan-less power supply -- more
expensive but well worth it if noise is a concern, but be sure to
monitor system temperatures to make sure cooling is adequate.
For cases and power supply here are some things to consider:
Form factor
Form factor is the specification that provides the physical
measurements for the size of components and where mounting devices for
them are located.
- EATX or Extended ATX boards are 12"x13". This format is almost exclusive to workstation computers.
- ATX is the most common form factor and is the de facto standard. In this form factor the motherboard is (usually) vertically mounted for more space and more efficient cooling than some other standards.
- microATX, or µATX, is smaller than standard ATX, but at the cost of fewer expansion slots. Many cases that support ATX also allow micro-ATX. Flex ATX is even smaller than micro-ATX, but only allows 2 expansion slots.
- WTX is intended for workstations and servers. Note: WTX has been discontinued as of 2008.
- BTX is another formfactor designed for more efficient cooling.
- PicoBTX 8"x10.5"
- MicroBTX up to 10.4"x10.5"
- BTX up to 12.8"x10.5"
- Mini-ITX is even smaller than BTX, at 6.75" square.
- NLX
Many OEM computers use non-standard form factors. Be sure to choose a motherboard compatible with your case's form factor.
Number of storage drive spaces
Internal hard drives/floppy drives (which go in the small 3.5" bays)
and internal CD/DVD drives (which go in the large 5.25" bays) take up
space in the case, so make sure you consider how many drives you will
need and what size slot they require. Note that optical drives and
floppy drives will need what are called "external" slots (meaning they
have a hole in the case through which their face can be accessed), while
hard drives do not need to be manipulated manually often, so they can
usually go into an "internal" slot. This is not to be confused with an
external drive, which doesn't go into the case at all.
Note that it's possible to buy adapters to fit items that go in small
bays (usually hard drives) into large bays. It is, however, not
possible to do the reverse.
Power rating
The power supply you choose needs to supply enough DC current to run
your components. Beyond that it needs to supply stable, accurate
voltages, i.e. the 12 volt rail needs to supply 12 volts (within normal
tolerances of 10% or so) steadily under any foreseeable load, likewise
the 3 and 5v rails at their respective voltages. Cheap power supplies
tend to fall down in these areas. There are several tech-heavy websites
that actually throw a multimeter on the PSU in the course of a review,
seek these out and make sure you select a quality PSU.
In selecting a power supply, check carefully that it has the power
feeds you need, e.g. six-pin PCI power, 20 vs. 24-pin motherboard
connectors, etc. If you are planning on running two video cards in SLI
(NVIDIA) or Crossfire (ATI) mode, make sure your power supply is
approved for that. Both companies have certification programs.
There are several calculators that try to help you select an adequate PSU for your system, such as:
Choose an efficient PSU. Efficient PSUs run cooler and more quietly
and thus do not create as much noise (important if you plan to sleep (or
think) in the same room with it or use it as a media center PC).
More information about this can be found at Silent PC Review, OCAU Wiki, among others.
Fans
Most cases mount one or more case fans, distinct from the fans that
may be attached to the power supply, video card and CPU. The purpose of a
case mounted fan is to move air through the system and carry excess
heat out. This is why some cases may have two or more fans mounted in a
push-pull configuration (one fan pulls cool outside air in, the other
pushes hot interior air out). The more air these fans can move, the
cooler things will generally be.
Fans for case cooling currently come in two common sizes, 80 mm and
120 mm, and computer cases tend to support one size or the other. The
larger 120 mm fans spin more slowly while moving a given volume of air,
and slower fans are usually quieter fans, so the 120 mm fans are
generally preferred, even though they cost a little more. Good 80 mm
fans can still be fairly quiet, so while fan size is a factor, it
shouldn't be a deal-breaker if the case has other features you like.
Make sure the power plug on the chosen case fan is supported by your
motherboard; 3- and 4-pin Molex connectors are common. Fans can also be
powered directly by the PSU, but in that configuration, the motherboard
can't control or report the fan's speed.
Variable speed fans with built-in temperature sensing are available,
but they may need to be specially ordered from an electronics supply
warehouse. They also may not have power plugs attached to their wire
leads, but this can be remedied by a competent technician. Variable
speed fans tend to run quieter than constant speed fans, as they only
move as much air as needed to maintain a set temperature within the case
or the power supply box. Under typical operating conditions they may be
barely audible.
Since fans run continuously when the computer is turned on, bearing
selection may be important for long life. The least expensive fans use sleeve bearings.
As the fan ages, the lubricant in the sleeve bearing dries out and
eventually the bearing wears, allowing the fan blade to nutate or
vibrate, making it very noisy. In severe cases the bearing may seize and
the fan will stop turning entirely, possibly jeopardizing the computer
when ventilation fails. The most expensive fans tend to be those that
use ball bearings, but they also have very long service lives. It
isn't uncommon for a ball bearing fan to run continuously for 7 to 10
years — possibly longer than the useful technological life of the
computer within which it is mounted. Ball bearing fans tend to be
slightly noisier than sleeve bearing fans. A fairly recent type of fan
bearing is a magnetic or "maglev" bearing, which uses a
magnetic field to suspend the fan rotor without physical contact. Such
fans exhibit practically zero bearing wear and barring a failure in
their motor drive components, have essentially an infinite service life.
Maglev bearings also tend to be completely silent, and when used in a
variable speed fan, can produce practically silent ventilation.
CPU (processor)
We discuss choosing a CPU in the next chapter, How To Assemble A Desktop PC/Choosing the parts/CPU.
Motherboard
The motherboard is a very important part of your computer. The
difference between a cheap and a quality motherboard is typically around
$100. A good motherboard allows a modest CPU and RAM to run at maximum
efficiency whereas a bad motherboard restricts high-end products to run
only at modest levels.
There are six things one must consider in choosing a motherboard: CPU
interface, Chipset, IDE or SATA support, Expansion slot interfaces, and
other connectors. One must also make sure that the motherboard is of a
form factor compatible with the case.
CPU interface
The CPU interface is the "plug" that your processor goes into. For
your processor to physically fit in the motherboard, the interface must
be an exact match to your processor. Intel currently has four
mainstream formats, the older Land Grid Array (LGA) 775 mostly for the
Core 2 chips, the LGA 1366 supporting their high-end Core i7 9XX CPUs
(as well as Xeon CPUs for servers), the LGA 1156 for mainstream i5 and
i7 CPUs, and the 1155 for the iX-XXXX (Sandy Bridge architecture) CPUs.
AMD currently uses six sockets AM3+, AM3, AM2+, AM2, 754 and 939. The
AM3 and AM3+ sockets are compatible with DDR3 RAM. The AM2+ socket is a
improved version of AM2. The AM2 sockets are faster (compatible with
DDR2 RAM) and more efficient than the older two. Socket 754 was aimed at
the value market, while Socket 939 was for performance applications.
Check with the motherboard manufacturer to ensure that the slot on
the motherboard will support the CPU you want to use. It is important to
know whether the motherboard's bus can support the exact CPU you plan
on using.
If the motherboard, CPU, and heatsink/fan are not compatible and
installed correctly, you can destroy the CPU and/or the motherboard in a
matter of seconds. Most modern processors come with a stock cooling fan
which will work well at stock speeds, stick with this if you have any
doubts.
Chipset
The function of BIOS is highly important. Some BIOS feature crash
proof functions essential for updating the firmware. Other motherboards
allow BIOS control of overclocking of CPU, RAM and Graphics card which
are much more stable and safer for overclocking. Newer BIOS have
temperature controls, and functions that shut down the computer if the
temperature gets too high.
IDE (ATA) or SATA interface
Used for connecting hard and optical drives, most motherboards used
to have two parallel, 40 pin IDE interface connectors which are now
mostly used for backwards compatibility if they are present. These old
PATA (parallel ATA) connections have been largely replaced by SATA
(Serial ATA) connections for hard drives and optical drives. SATA
connections are simple - one plug, one cable, one device.
In the older PATA/IDE standard up to two devices could be connected
to each port in a Master/Slave configuration. A 44 wire ribbon cable was
used for this connection with three connectors, one on each end and one
in the middle (actually slightly off center). One end was plugged into
the motherboard connection and the other end plugged into the first (or
only) device. If two devices are connected the second is connected to
the middle connection. The device plugged into the end must be
configured as a master (usually via a jumper on a set of pins on the
device) while the second must be configured as a slave – OR both must be
configured as “cable select”.
Two devices connected on the same IDE port can contend for access to
the bus, causing a reduction in the effective speed of the drives. The
newer serial ATA (SATA) interface has four or more separate motherboard
connections that allow independent access and can increase the speed at
which hard drives work. The cables are also narrower, improving the flow
of air inside the case.
The support for older (PATA) IDE drives is starting to disappear. The
new G/Q/P 965 chipset series from Intel completely dropped support for
such devices. Nevertheless, many motherboard makers are still including
an additional IDE controller on their boards, and it still remains
possible to buy an extra PCI IDE controller.
Expansion slot interfaces
Old motherboards may have one or more the following slots:
- AGP - for graphics cards (ranging from AGP 1x, 2x, 4x and 8x)
- PCI - for expansion cards and low-end graphics cards
ATI still manufactures PCI graphics cards, but for better performance
try a card supporting PCI-Express. AGP is not a good idea, because it
is a standard that is on its way out. You may come upon ancient
motherboards with neither AGP nor PCI, but please don't waste your time
trying to reuse them.
Due to the evolution of new graphics cards on the serial PCI-Express
Technology, current newer motherboards have the following connections:
- PCI-Express 16x for mainstream graphics cards (4 times speed of AGP 8x)
- PCI-Express 1x for faster expansion cards (replacing older PCI)
- PCI for use of old expansion cards (will eventually be phased out)
Older AGP 8x graphics cards are generally being discontinued in favor
of PCI-Express 16x, as the speed and efficiency is about 4 times that
of the AGP 8x technology. Old PCI cards are either now built into the
motherboard (for sound cards, LAN cards, IEEE 1394 firewire and USB 2.0
interfaces) or becoming PCI-Express variants.
Other connectors
- Universal Serial Bus (USB)
- In addition to the USB 2.0 ports provided on the back panel, most motherboards will have connectors for additional ports, either on the front of the case or in a panel that fits where a PCI card might otherwise be connected. USB 2.0 ports (and be sure that your chosen motherboard supports the faster 2.0 standard) are used for connecting various peripherals such as printers, external hard drives etc. USB connectors are also used for connecting MP3 players, some cameras and an assortment of less serious devices like fans, Nerf missile launchers and drink warmers. Given the growing popularity of USB devices, the more ports your motherboard supports, the better.
USB 3.0 ports are now available on some motherboards and they are
even faster than USB 2.0 — up to 5 Gbps. Although there are not many
devices available yet that support the USB 3.0 standard, USB 3.0 ports
are backwards compatible and can be used with USB 1 or 2 devices,
although these will not receive the benefit of USB 3.0 speeds.
- Serial (COM) or parallel (printer) ports
- Use of traditional 25-pin subminiature D parallel printer ports and RS-232 9-pin subminiature D serial ports has been waning since the early 1990s since the introduction of the Universal Serial Bus. Many motherboards no longer offer parallel ports — formerly used almost exclusively for connecting printers — altogether, while serial ports, which once numbered as many as four, are now usually solitary. The principal use for serial ports once was to connect to a mouse or an external modem; both of these devices now connect via USB. Unless you are connecting old peripheral hardware, these ports will be of minimal importance. Even so, USB-to-Parallel and USB-to-Serial adapter cables are available, allowing late model computers to communicate with older peripherals.
- IEEE-1394 Firewire
- Firewire ports are principally used for connecting DV (Digital Video) cameras and external hard drives. This technology got a foothold because it was much faster than USB 1.0 and 1.1. With the near-ubiquity of USB 2.0, however, Firewire 400, the original, and still the most common IEEE-1394 implementation, was actually a little slower. For this reason, and in spite of the existence of a faster but seldom implemented Firewire 800 specification, Firewire is not as popular as USB. Like USB, most motherboards that support Firewire will have one or more external ports on the back panel and the ability to connect one or more additional ports. One or two Firewire ports will suffice for most users.
Note that, regardless of the motherboard's native support, additional
ports of all kinds can always be added via a PCI or PCI-E 1 expansion
card.
Memory
The amount of random access memory (RAM) to use has become a fairly
simple choice. Unless one is building on a very restricted budget, one
just has to choose between installing one, two, four, or eight
gigabytes. One gigabyte of RAM is plenty for most modern operating
systems, but all of them will run a little faster with two or four
gigabytes. While 32-bit operating systems can address 4 gigabytes, they
can utilize little more than three gigabytes as system RAM (actually 4
gigabytes minus Video RAM minus overhead for other devices). If one
wishes to utilize the full 4 (or more) gigabytes of RAM, one needs to
install a 64-bit operating system. It really comes down to a financial
decision. One might also choose to get one gigabyte of high quality RAM
over two gigabytes of lesser quality, especially if one plans to
overclock. Some specialized applications may profit from more than two
gigabytes of RAM. If one plans on using such, make sure to check that
both the operating system and the motherboard will accommodate the
amount of RAM one has in mind.
Another thing to consider when choosing the amount of RAM for one's
system is the graphics card. Most motherboard-integrated graphics chips
and PCI Express graphics cards marketed with the "Turbo Cache" feature
will use system memory to store information related to rendering
graphics; this system memory is generally not available at all to the
operating system. On average, these graphics processors will use between
64 megabytes and 512 megabytes of system memory for rendering purposes.
The actual type of RAM one will need depends on the motherboard and
chipset one gets. Some old motherboards use DDR (Double Data Rate) RAM,
but the industry standard is now DDR2. DDR3 is coming on strong on the
high end and is required for Intel's new Core i7 processors. Chip sets
that use dual-channel memory require one to use two identical — in terms
of size and speed — RAM modules. The RAM should usually operate at the
same clock speed as the CPU's Front Side Bus (FSB). The motherboard may
not be able to run RAM slower than the FSB, and using RAM faster than
the FSB will simply have it run at the same speed as the FSB. Buying
low-latency RAM will help with overclocking the FSB, which can be of use
to users who want to get more speed from their systems.
If one is upgrading an existing computer, it is best to check if
one's machine requires specific kinds of RAM. Many computer OEMs, such
as Gateway and Hewlett-Packard, require custom RAM, and generic RAM
available from most computer stores may cause compatibility problems in
such systems.
Labeling of RAM
RAM is labeled by its memory size in megabytes (MB) and clock speed (or bandwidth).
SDRAM (Synchronous Dynamic RAM) is labeled by its clock speed in
megahertz (MHz). For example, PC133 RAM runs at 133 MHz. SDRAM is nearly
obsolete, as nearly all motherboards have withdrawn support for SDRAM.
It is now superseded by the more efficient DDR RAM.
- 128MB SD-133 = 128MB PC133 RAM
DDR RAM can be labeled in two different ways. It can be labeled by
approximate bandwidth; as an example, 400MHz-effective DDR RAM has
approximately 3.2 GB/s of bandwidth, so it is commonly labeled as
PC3200. It can also be labeled by its effective clock speed; 400 MHz
effective DDR RAM is also known as DDR-400. There is also DDR and DDR2
labeled as PC and PC2.
- 256MB DDR-400 = 256MB PC 3200 RAM
- 256MB DDR2-400 = 256MB PC2 3200 RAM
DDR RAM has three versions: DDR (also DDRI), DDR2 (or DDRII) and DDR3
- DDR supports DDR-200, DDR-266, DDR-333, DDR-400 (mainstream) and DDR-533 (rare)
- DDR2 supports DDR-400, DDR-533, DDR-667, DDR-800, DDR-1066
- DDR3 supports DDR-1333 to DDR-2000
Hard drive
Things to consider when shopping for a hard drive:
- Interface
- The interface of a drive is how the hard drive communicates with the
rest of the computer. The following hard drive interfaces are
available:
- Parallel IDE drives (PATA, also known as ATA or IDE) use cables that can be distinguished by their wide 40-pin connector, colored first-pin wire, and usually gray "ribbon" style cables. This technology is largely obsolete because SATA uses thinner cables, eliminates contention for the IDE bus that can occur when two PATA drives are attached to the same connector, and promises faster drive access.
- SATA drives have the advantages outlined above. If you want Serial ATA, you will either need to purchase a motherboard that supports it (all newer motherboards do), or purchase a PCI card that will allow you to connect your hard drive. Note that some older motherboards will not allow you to install Windows XP to a Serial ATA hard drive.
- SCSI, although more expensive and less user friendly, is usually worthwile on high performance workstations and servers. Few consumer desktop motherboards built today support SCSI, and when building a new computer, the work needed to implement SCSI may be outweighed by the relative simplicity and performance of IDE and SATA. SCSI hard drives typically reach rotational speeds of up to 15,000 RPM, and are more expensive.
- USB can be used for connecting external drives. An external drive enclosure can convert an internal drive to an external drive.
- IEEE1394 This format is most commonly known as "Firewire" (Apple) or "I link" from Sony. The theoretical speed of IEEE1394 is double that of USB 1.0.
- Cache
- The cache of a Hard drive is a faster media than the hard drive itself and is normally 2MB (in low-end), 8MB (standard), or 16MB (large disks only). The existence of a cache increases the speeds of retrieving short bursts of information, and also allows pre-fetching of data. Larger cache sizes generally result in faster data access.
- Form factor
-
- 3.5 inch drives are usually used in desktops.
- 2.5 inch drives are usually used in laptops.
- Capacity
- The smallest desktop drives that are widely available hold about 160 gig of data, although the largest drives available on the market can contain 3TB (3000GB). Few people will need disks this large - for most people, somewhere in the range of 300-750GB will be sufficient. The amount of space you will need can depend on many factors, such as how many high-end games and programs you want to install, how many media files you wish to store, or how many high-quality videos you want to render. It is usually better to get a hard drive with a capacity larger than you anticipate using, in case you need more in the future. If you run out of space, you can always add an additional hard drive using any free IDE or Serial ATA connector, or through an external interface, such as USB or FireWire.
- Rotational Speed
- The speed at which the hard drives platters spin. Most laptop (2.5 inch) drives spin at 5400 RPM, while common desktop drives come in at 7200. There are PATA and SATA drives that spin at 10,000 RPM and some SCSI drives hit 15,000. However drives above 7,200 RPM usually have limited capacity, and a much higher price than comparable 7,200RPM drives, making such drives advisable only when the fastest possible speeds are required.
- Noise and Heat
- Modern hard drives are fairly quiet in operation though some people are sensitive to the faint hum and occasional buzz they do make. If your HD is loud, it’s time to think about replacing it. Hard drives will also throw some heat and adequate air circulation should be provided, usually by case fans. There is software available that will allow you to monitor both the health and temperature of your hard drive(s), it’s a good idea to check from time to time.
- Warranty
- Many manufactures offer warranties ranging from 30 days (typically OEM) up to five years. It is well worth spending an extra few dollars to get the drive that carries a longer warranty.
Secondary components
These components are important to your computer, but are not as central as the Core Components.
Video output
For a computer to use a display for monitoring it will need some form
of video card into which a display can be plugged. The majority of home
and office computers, which predominantly use 2D graphics for office
applications and web surfing can use an 'onboard' or integrated graphic
processor which will be included on most low to mid range motherboards.
For gaming, or 3D modeling, a good quality graphics card will be needed.
Currently, two companies dominate the 3D graphics accelerator market;
nVIDIA and ATI. nVIDIA and ATI build their own graphics products, and
license their technologies to other companies. Both companies make a
complete line of cards with entries at every price/performance level,
and each brand has its own supporters. Video cards have their own RAM,
and many of the same rules that govern the motherboard RAM field apply
here: to a point, the more RAM, and the faster it is, the better the
performance will be. Most applications require at least 128MB of video
RAM, although 512MB is rapidly becoming the new standard. On the other
end, 1GB video cards top the consumer end of the video card market. As a
rule of thumb, if you want a high end video card, you need a minimum of
756MB of video memory -- preferably 1GB. Don't be fooled, though;
memory is only part of the card and the actual video processor is more
important than the memory.
It is generally better to choose your video card based on your own
research, as everyone has slightly different needs. Many video card and
chip makers are known to measure their products' performances in ways
that you may not find practical. A good video card is often much more
than a robust 3D renderer; be sure to examine what you want and need
your card to do, such as digital (DVI) output, TV output,
multiple-monitor support, built-in TV tuners and video input. Another
reason you need to carefully research is that manufacturers will often
use confusing model numbers designed to make a card sound better than it
is to sell it better. For example, the Geforce 4 MX series of cards
claim to be a "Geforce 4," however, the actual processor is closer to a
Geforce 2, only more powerful, meaning that these cards actually lack
many features available even to the Geforce 3 series. However, when
these cards were first produced, they were considerably cheaper than a
real Geforce 4 (the TI series) making them an ideal choice if you were
more interested in working on a spreadsheet than in playing games. For
this sort of reason, you have to carefully pick your card depending on
your needs. TV outputs can easily be adapted to your computer by using a
DVI - Component Video cable.
Newer technologies such as SLI and Crossfire allow the use of two
video cards to render the same video scene, similar to using two CPUs or
a dual-core CPU. These systems tend to be expensive, as only some video
cards offer this option, and you'll need two of them. However, it can
be a useful upgrade path to consider. A SLI-capable motherboard is
usually not much more expensive than the regular model, and will work
fine with a single video card. You can use it with one card now, and buy
another one in the future (which will probably be much cheaper by
then), which means you will take advantage of your old video card too.
Interface
There are four different current graphics card interfaces: integrated, PCI, AGP and PCI-Express.
Most retail computers will ship with an integrated graphics card. It
is important to understand that an integrated graphics card uses the
system's RAM, and relies heavily on your system's CPU. This will mean
slow performance for graphic-intensive software, such as games. Most
motherboards that have integrated graphics will also have one of the
other three slot interfaces available so it isn't hard to place a new
card to suit your needs if the need ever arises.
Older video cards use the standard PCI slots that are now growing
obsolete due to limited speed and memory. These cards are needed for a
few rare systems lacking an AGP or PCI-E slot (usually low end desktop
systems designed to be cheap.) They are also useful for adding
additional video cards to a system.
Although the AGP standard has now, by and large, been superseded by
PCI-E, the cards are still available as are a few motherboards that
support them. There are 4 different speed and bandwidths of AGP, 1x, 2x,
4x and 8x. While 8x is the fastest and most common for high end
products, the true performance of your AGP card is limited by the lower
AGP value of your graphics card and motherboard. For example, an AGP 8x
card on a 4x motherboard can only run at up to 4x. AGP has mostly been
phased out and there will not be an AGP 16x due to technical
limitations.
The newest trend in graphics card is the PCI-Express (not to be confused with PCI-X)
system that supports up to 16x speeds. Some graphics cards still come
in both AGP and PCI-E 16x models but the newest models of graphics cards
are often PCI-E 16x only. While most motherboards have only one PCI-E
16x slot, those with two such slots can combine the power of two video
cards using technologies known as SLI for NVidia, and CrossFire for ATI.
However, you will have to match the video cards to a motherboard
supporting the multiple card technology of choice, and use two similar
video cards that both support dual video cards.
Keep in mind that to provide best picture quality your graphics card
must be capable of displaying the same resolution as your LCD display's
native resolution.
CD/DVD
Optical drives have progressed a long way in the past few years, and
you can now easily purchase DVD writers that are capable of burning 9GB
of data to a disk for an insignificant amount of money. Even if you
don't plan on watching or copying DVDs on your computer, it is still
worth purchasing a burner for their superior backup capabilities.
When purchasing a DVD writer, you will want one that is capable of
burning both the '+' and '-' standards, and it should also be Dual Layer
compatible. This will ensure that you can burn to almost all recordable
DVDs currently on the market (the other major format, DVD-RAM is almost
unused, for the most part, so don't worry about it).
Floppy drive
Though Floppy drives have been made largely obsolete in recent years
by devices such as USB "Thumb Drives" and CD writers, they are often
installed anyway because they are sometimes required for BIOS updates
and exchanging small files with older computers. Floppy drives block air
movement with wide cables, and can make computers set to check the
drive take longer to start (most have an option in their BIOS to disable
this.). One option to overcome the cable problem and to make it easier
to install is to buy an external USB floppy drive, these are potentially
a little bit faster and can be plugged into a different system (such as
a laptop without a floppy drive.) However, not all systems support
booting from a USB floppy drive -- most notably older motherboards.
It should be noted that floppy disks are not suitable for long term
storage of data, even in a backup role. Never keep your only copy of an
important file on a floppy disk.
Sound card
Most motherboards have built-in sound features. These are often
adequate for most users. However, you can purchase a good sound card and
speakers at relatively low cost - a few dollars at the low end can make
an enormous difference in the range and clarity of sound. Also, these
onboard systems tend to use more system resources, so you are better off
with a real sound card for gaming.
Sound card quality depends on a few factors. The digital-analog
conversion (DAC) is generally the most important stage for general
clarity, but this is hard to measure. Reviews, especially those from
audiophile sources, are worth consulting for this; but don't go purely
by specifications, as many different models with similar specs can
produce completely different results. Cards may offer digital (S/PDIF)
output, in which case the DAC process is moved from your sound card
either to a dedicated receiver or to one built into your speakers.
Sound cards made for gaming or professional music tend to do
outstandingly well for their particular purpose. In games various
effects are oftentimes applied to the sound in real-time, and a gaming
sound card will be able to do this processing on-board, instead of using
your CPU for the task. Professional music cards tend to be built both
for maximum sound quality and low latency (transmission delay) input and
output, and include more and/or different kinds of inputs than those of
consumer cards.
Modem
A modem is needed in order to connect to a dial up Internet
connection. A modem can also be used for faxing. Modems can attach to
the computer in different ways, and can have built-in processing or use
the computer's CPU for processing.
Modems with built-in processing generally include all modems that
connect via a standard serial port, as well as any modems that refer to
themselves as "Hardware Modems". Software Modems, or modems that rely on
the CPU generally include both Internal and USB modems, or have
packaging that mentions drivers or requiring a specific CPU to work.
Modems that rely on the CPU are often designed specifically for the
current version of Windows only, and will require drivers that are
incompatible with future Windows versions, and may be difficult to
upgrade. Software Modems are also very difficult to find drivers for
non-Windows operating systems. The manufacturer is unlikely to support
the hardware with new drivers after it is discontinued, forcing you to
buy new hardware. Most such modems are internal or external USB, but
this is not always the case.
Modems can be attached via USB, a traditional serial port, or an
internal card slot. Internal and USB modems are more easily autodetected
by the operating system and less likely to have problems with setup.
USB and serial port modems often require an extra power supply block.
Gaming modems are normal modems that default to having a low
compression setting to reduce lag, but are generally no longer used by
gamers, who prefer broadband connections.
Network interface card
A Network interface card, or Ethernet card, is required in order to
connect to a local area network or a cable or DSL modem. These typically
come in speeds of 10Mbps, 100Mbps, or 1000Mbps (gigabit); these are
designated as 10Mbps, 10/100Mbps, or 10/100/1000Mbps products. The
10/100 and 10/100/1000 parts are most commonly in use today. In many
cases, one or two Ethernet adapters will be built into a motherboard. If
there are none, you will have to purchase one. These typically are
inserted into a PCI slot. To get the full speed of 10/100/1000Mbps
Ethernet, it's best to get a motherboard with that connector built in. A
typical Ethernet card usually costs around US$13.
Peripherals
Anything outside the case that connects to your computer is
considered a peripheral. The keyboard, mouse and monitor are pretty much
the bare minimum you can go with and still be able to interact with
your computer. Your choice in peripherals depends on personal preference
and what you intend to do with your computer.
Mouse and keyboard
There are, broadly, two types of mouse: optical and mechanical.
Mechanical mice use a rubber coated ball bearing that contacts the
mousepad or other surface and actually rolls around. Optical mice use a
bright light and a sensor to track the movement of the mouse.
When choosing a mouse, there is generally no reason not to choose an
optical mouse. They are considerably lighter (and as such, reduce RSI)
as they have no moving parts, they are much better at smoothly tracking
movement, and they don’t require constant cleaning like ball mice
(though it may be wise to brush off the lens with a q-tip or other soft
tool on occasion). Make sure that you spend money on a decent-quality
mouse made by companies such as Microsoft or Logitech, as lower-end
optical mice will skip if moved too fast. Mice of medium-to-high quality
will track your movement almost flawlessly.
Although three buttons are generally enough for operating a computer
in normal circumstances, extra buttons can come in handy, as you can add
set actions to each button, and they can come in handy for playing
various video games. One thing to note is that with some mice those
extra buttons are not actually seen by the computer itself as extra
buttons and will not work properly in games. These buttons use software
provided by the manufacturer to function. However, it is sometimes
possible to configure the software to map the button to act like a
certain keyboard key so that it will be possible to use it in games in
this manner.
Wireless keyboards and mice do not now display the sort of noticeable
delay that they once did, and now also have considerably improved
battery life. However, gamers may still want to avoid wireless input
devices because the very slight delay may impact gaming activities,
though some of the higher end models have less trouble with this. The
extra weight of the batteries can also be an inconvenience.
Printer and scanner
For most purposes, a mid-range inkjet printer will work well for most
people. If you plan on printing photos, you will want one that is
capable of printing at around 4800dpi. Also, you will want to compare
the speed of various printers, which is usually listed in ppm (pages per
minute). When choosing a printer, always check how much new cartridges
cost, as replacement cartridges can quickly outweigh the actual
printer's cost. Be aware of other possible quirks as well. For example,
Epson has protection measures that make refilling your own ink
cartridges more difficult because an embedded microchip that keeps track
of how much ink has been used keeps the printer from seeing the
cartridge as full once it has been emptied.
For office users that plan to do quite a bit of black and white
printing buying a black and white laser printer is now an affordable
option, and the savings and speed can quickly add up for home office
users printing more than 500 pages a month.
Scanners are useful, especially in office settings, they can function
with your printer as a photocopier, and with software can also interact
with your modem to send Faxes. When purchasing a Scanner, check to see
how "accessible" it is (does it have one-touch buttons), and check how
good the scanning quality is, before you leave the store if possible.
Finally, "Multi-Function Centres" (also called
"Printer-Scanner-Copiers") are often a cost-effective solution to
purchasing both, as they take up only one port on your computer, and one
power point, but remember that they can be a liability, since if one
component breaks down, both may need to be replaced.
Display
When choosing a display for your computer, you have two choices: a
Cathode Ray Tube (CRT) screen, or a Liquid Crystal Display (LCD) screen.
Both technologies have their advantages and disadvantages but CRT's,
now nearly obsolete, are almost unavailable new - making the argument
moot. Used CRT's on the other hand, can be had nearly for free and still
work if you have the room for them.
LCD panels
Liquid Crystal Displays (LCDs) have the advantage of being a
completely digital setup, when used with the DVI-D or HDMI digital
connectors. When running at the screen's native resolution, this can
result in the most stable and sharp image available on current monitors.
Many LCD panel displays are sold with an analog 15-pin VGA connector
or, rarely, with an analog DVI-I connector. Such displays will be a bit
fuzzier than their digital counterparts, and are generally not preferred
over a similarly-sized CRT. If you want an LCD display, be sure to
choose a digital setup if you can; however, manufacturers have chosen to
use this feature for price differentiation.
The prime disadvantage of LCDs is "dead pixels", small, failed areas
on your monitor, which can be very annoying, but generally aren't
covered under warranty; this can make purchasing LCD displays a
financial risk. In fact, most LCD panel manufacturers allow for a
certain number of dead pixels in their product specification.
LCDs are acceptable for fast-paced gaming, but you should be sure
that your screen has a fairly fast response time (of 12 ms or lower) if
you want to play fast games. Nearly all flat panels sold today meet this
requirement, some by a factor of 3.
When picking an LCD, keep in mind that they are designed to display
at one resolution only, so, to reap the benefits of your screen, your
graphics card must be capable of displaying at that resolution. That in
mind, they can display lower resolutions with a black frame around the
outside (which means your entire screen isn't filled), or by stretching
the image (which leads to much lower quality). Running at a higher
resolution than your monitor can handle will either make everything on
the screen smaller, at a significant quality drop, or will display only a
part of the screen at a time.
CRT (cathode ray tube) displays
The other key type of display is the Cathode Ray Tube (CRT) display.
While CRT technology is older, it often outperforms LCD technology in
terms of color reproduction (color gamut), although LCD displays are
quickly catching up. CRTs are becoming increasingly difficult to find
and have almost vanished from mass-market retail. High end CRT's are
still available, though they are rapidly being discontinued, and now
cost a considerable amount.
There are two types of CRT displays, shadow mask and aperture grill.
An aperture grill display is brighter and perfectly flat in the
vertical direction, but is more fragile and has one or two
mostly-unnoticeable thin black lines (support wires) running across the
screen. CRTs are generally two to four times as deep as similarly-sized
LCDs, and can weigh around 10 times as much. If you purchase a CRT
display over the Internet, shipping is much more expensive than an LCD,
due to the significantly greater weight.
Sometimes CRTs with a flat screen instead of a curved one are called
"flat screens". This is not to be confused with the term "flat panel",
used to refer to LCDs. In order to withstand atmospheric pressure, the
glass at the front of a flat screen CRT needs to be very thick, and thus
they are limited to diagonal sizes of 20 inches, or so. A flat screen
CRT will be noticeably heavier than its curved screen counterpart.
For improved contrast and readability, some CRTs were manufactured
with an anti-reflection coating. Such tubes make colors appear more
vibrant and blacks appear jet black. Also, if the user has a light from
behind, such as from a lighting fixture or windows, annoying reflections
on the screen will be much less noticeable. The coating typically
consists of magnesium fluoride, the same material used to coat binocular
optics and some corrective eyeglass lenses. It is relatively soft, and
must be cleaned with care, using special lens cleaning cloths or papers
to prevent scratching of the coating. Another way to clean them is with a
boiled 100% cotton flannel cloth and commercial glass cleaning
solution, such as Windex. Oily fingerprints show up very clearly on
coated screens, so one should avoid touching them. With reasonable care,
however, the screen may only need to be wet-cleaned once a year and in
the meantime can be wiped with a soft dust cloth or brushed with a soft,
natural-bristle paint brush to remove any dust that may accumulate. If
you're shopping for such a display on the used market, you will
recognize it by the faint, purplish reflection of room lights and
daylight.
Lower-end CRTs use an etched glass tube face. It gives the glass a
dull, non-specular appearance that helps cut down on glare, but such
tubes do not provide the high contrast and color brilliance of tubes
treated with an anti-reflection coating.
Flicker in CRT's can cause headaches in some people when run at lower
frequencies, so it may be ideal to pick a screen offering higher
vertical refresh rates at whichever resolutions you intend to use. Most
people who have problems with low frequencies (60 Hz) find it preferable
to have at least 80 Hz at the intended resolution. Many won't be
bothered by this at all, however.
CRT displays and early LCD displays were developed at a time when
television and computers used screens with 4:3 (width x height) aspect
ratios. If your application requires a wide-screen display, even at the
expense of reduced performance, a modern 16:9 aspect ratio LCD screen
should be chosen instead.
Speakers
Computer loudspeaker sets come in two general varieties; 2/2.1 sets
(over a wide range of quality), and "surround", "theater", or "gaming"
sets with four or more speakers, which tend to be somewhat more
expensive. A 2-speaker set is adequate for basic stereophonic sound. A
2.1-speaker set adds a sub-woofer to handle low frequencies. Low-end
speakers can suffer from low bass response or inadequate amplification,
both of which compromise sound quality. Powered speakers with separate
sub-woofers usually cost only a little more and can sound much better.
At the higher end, one should start to see features like standard audio
cables (instead of manufacturer-specific ones), built in DACs, and a
separate control box.
The surround sets include a sub-woofer, and two or more sets of
smaller speakers. These support 5.1 or 7.1 standards that allow sound to
be mixed not only left and right, as with standard stereo speakers, but
front and back and even behind the listener. Movies and video games
make use of this technology to provide a full-immersion experience. Make
sure your sound hardware will support 5.1 or 7.1 before buying such a
speaker system. If your budget allows, you can avoid the computer
speaker market entirely and look into piecing together a set of
higher-end parts. If you are buying a speaker system designed for PCs,
research the systems beforehand so you can be certain of getting one
that promises clarity rather than just raw power. Speaker power is
usually measured in RMS Watts. However, some cheap speakers use a
different measure, Peak Music Power Output (PMPO), which appears much higher.
Headphones can offer good sound much more cheaply than speakers, so
if you are on a limited budget, but want maximum quality, they should be
considered first. The advantage of headphones is that the acoustic
environment between the audio driver is fully contained and controlled
within the earcups and is not dependent on room acoustics. There are
even headphones which promise surround-sound, though these have not been
favorably reviewed.
You will love it to enjoy our new app Idle Heroes Mod Apk: which you can download and enjoy free.
ReplyDelete